Marantec Reference Switch for Belt and Chain Rails

• This part works with the positioning tab and motor to determine the open & close limits of the actual garage door.

Marantec Shaft Adapter

Marantec Trolley Assembly (Slider)

• Replaces #8030177 and #803178
• Replacement trolley assembly for chain & belt rail assemblies
• Fits Marantec opener models: M4500M4500eM4700M4700eQ7500Q7700
• Works for 7' 8' & 10' high doors (red pull cord rope can be adjusted to length accordingly)
• Note: will not work for the Heavy Duty (2mm-14ga.) rail assembly
• Same part number as 91570

Marantec Belt Connector Kit

• Works for all Marantec Belt Drive Openers
• For models: Mac Lift M4500M4700Q7500Q7700 M4500e M4700e
• Includes two connector pieces and four screws
• Not for use on the heavy duty rails used by Q7900 & M4900e

Marantec Chain Connector Kit

• Works for all Marantec Chain Drive Openers
• For models: Mac Lift M4500M4700Q7500Q7700 M4500e M4700e
• Includes two connector pieces and four screws
• Not for use on the heavy duty rails used by Q7900 & M4900e

Marantec Replacement Belt with Tab for 8ft Door

• Overall Belt Length = 250"
• Travel limit tab attached to belt
• For Marantec opener models: M4500 M4700 Q7500 Q7700 Q7900 M4500e M4700e M4900e Synergy 260 Synergy 270 Synergy 280 Synergy 360 Synergy 370 Synergy 380 Synergy Solo
• Check the Belt Connector while you are replacing the belt. If it's worn or cracked it should also be replaced

Marantec Power Board for RV- 8000 & LC-1000 Models

Marantec Logic Board for Non-EOS Models

• For use on M Line- M-4500 and M-4700 models.
• For use on Q Line - 7500 and 7700 models.
• For use on Martin DC 3500E and DC 3700E models.
• Replaces 8054216. Special programming needed. Instructions included

Marantec Relay Power Board for M4500 Models

• Same as # 83364

Marantec Sprocket Holder Assbly For Heavy Duty 1.2mm Belt Rails Only

• Compatible with Marantec Heavy Duty (1.2mm - 18 gauge) 2-Piece & Standard Belt Rail
• Compatible with Marantec models: LC1000 M4500 M4500e M4500eI M4700 M4700e M4700eI M4900e Q7500 Q7700 Q7900 Synergy 260 Synergy 270 Synergy 280 Synergy 360 Synergy 370 Synergy LC and Synergy Solo
• Compatible with Marantec belt rails: M13-1207B M13-1208B M13-1210B M13-1212B. M13-1214B

Marantec RPM Sensor with Wire Harness

• For use on M-line/Q-line/EOS models

Marantec Sprocket Holder Assbly Standard Belt Rail

• Compatible with Belt Standard Rail
• For Marantec belt opener models: Synergy 260 Synergy 270 Synergy 280 Synergy 360 Synergy 370 Synergy 380 Synergy Solo M50 M55
• Not for use on the heavy duty 1.2mm - 18 gauge rails
• Measures 5"x2-3/4"x1-1/4"

Marantec Front Idler Assembly

• Complete Roller holder assembly for ML-Series rails
• Used for belt and chain drive opener rails
• Same as # 8030432

Marantec 2 Piece Logic Board with Terminal Strip for EOS Models

• For use on Easy Operating System (EOS) units 4500E 4700E and M50.
• Includes the terminal strip for direct replacement of boards that had a power surge or burned out.
• The marantec old model number was 78914 it is now 97798.

Marantec Shark Tooth Position Reference Tab Belt Rail (96834)

• Same as part number 96834
• For belt rail

Marantec Shark Tooth Position Reference Tab Chain Rail

• For chain rails.
• This part is installed inside rail on the actual chain.
• This part works with the reference switch to determine the open & close limits of the garage door.
• Reference switch part # 104083

Marantec Photoeyes 69190 / 97246

• Works on all Marantec units
• Includes brackets hardware and wiring
• Same as item #86850 97246 used to be M4-705
• Made in Germany